Technical Specifications
SPL
104 dB
Amplifier Power
72 W Bass (Class D) + 36 W Midrange (Class D) + 36 W Treble (Class D)
Frequency Response
45 Hz - 37 kHz ("-6 dB")
Accuracy of Frequency Response
± 1.5 dB (58 Hz - 20 kHz)
Driver Dimensions
2 x H 65 x W 130 mm Bass + ⌀ 90 mm Midrange + ⌀ 19 mm Treble (view in inches)
Dimensions
H 305 x W 189 x D 212 mm, with Iso-Pod™ (view in inches)
Weight
6.7 kg / 14.8 lb
Connections
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
8331A SAM™ Studio Monitor
SAM™ Studio Monitor
Technical Specifications
Incredible three-way point source monitor with the footprint of a compact two-way. When space and precision is of the essence, nothing even comes close.
System Specifications
Frequency Response
58 Hz - 20 kHz (± 1.5 dB)
Low cutoff -6dB
45 Hz
High cutoff -6dB
37 kHz
SPL
Peak SPL Maximum peak acoustic output per pair in a listening room with music material at 1 m.
≥110 dB
Short term max SPL Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥104 dB
Long term max SPL Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
≥99 dB
Self-generated noise
Self-generated noise Self generated noise level in free space at 1 m on axis (A-weighted).
≤0 dB SPL
Weight
Weight6.7 kg (14.8 lb)
Dimensions
Height
285 mm
Height with Iso-Pod
305 mm
Width
189 mm
Depth
212 mm
Enclosure
Enclosure material
Die cast aluminium
Enclosure type
Reflex port
Drivers
Driver type
Racetrack
8331A Bass Driver
Count
2
Width
130 mm
Height
65 mm
Driver type
Coaxial
8331A midrange driver in cone (coaxial)
Diameter
90 mm
Driver type
Coaxial
8331A treble driver in metal dome (coaxial)
Diameter
19 mm
Directivity
Harmonic distortion
> 100 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF (top graph)
3.2 ms
Extended Phase Linearity in GLM set to ON (bottom graph)
6.9 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
72 W Class D
36 W Class D
36 W Class D
Mains voltage
100-240 VAC 50/60Hz
Power consumption
ISS Active
≤0.5 W
Idle
≤4 W
Full output
60 W
Signal processing section
Connectors
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
Crossover
Bass/Mid
500 Hz
Mid/Treble
3000 Hz